Drip Irrigation: How Long to Run Your System

Why Drip Irrigation?

Drip irrigation delivers water directly to the root zone through emitters, with 85-95% efficiency — compared to 75-85% for sprinklers and 50-70% for flood/furrow. Benefits: 30-60% water savings, reduced weed growth (water only where crops grow), less disease (foliage stays dry), nutrient application through fertigation, and automation potential. Drip is ideal for vegetables, orchards, vineyards, and high-value row crops. It is less suitable for closely spaced crops like wheat orice (unless using drip tape). Ce guide couvre calculateur temps irrigation et les calculs agricoles associés pour vous aider à optimiser les opérations de votre ferme.

Key Components and Specifications

Emitter Flow Rate

Common emitter flow rates: 0.5 GPH (2 L/h) — for sandy soils, close spacing, small plants. 1 GPH (4 L/h) — standard for most vegetables and medium soils. 2 GPH (8 L/h) — for clay soils, wide spacing, large plants (trees, vines). 4 GPH (16 L/h) — for mature trees, high water demand. Pressure-compensating emitters maintain consistent flow regardless of pressure variations (important for long rows or hilly terrain). Non-compensating emitters are cheaper but flow varies with pressure.

Emitter Spacing

Spacing depends on crop and soil: Sandy soil: 20-30 cm (water moves down, not sideways). Loam: 30-50 cm. Clay: 50-75 cm (water movesideways more). Close-spaced crops (lettuce, strawberries): 15-30 cm. Row crops (tomato, pepper): 30-50 cm (one or two emitters per plant). Orchards/vineyards: 50-100 cm (multiplemitters per tree). The goal is overlapping wetting patterns — each plant's root zone should be fully wetted.

Pressure and Filtration

Most drip systems operate at 10-15 psi (0.7-1.0 bar). Too high pressure = emitter damage, uneven flow, misting. Too low = insufficient flow, uneven watering. Use a pressuregulator at the system inlet. Filtration is critical — emitters clog easily. Use: Screen filter (150 mesh) for clean water (municipal, well). Disc filter (120-150 mesh) for surface water (pond, canal). Sand/media filter for dirty water (canal, river with sediment). Flush lines monthly and inspect emitters quarterly.

Calculating Runtime

Step-by-Step Method

1. Determine daily crop water requirement (ETc = ETo × crop coefficient). Use local weather station data or evapotranspiration charts.

2. Calculate water needed per plant: Daily water (L) = ETc (mm/day) × plant area (m²) × 0.85 (efficiency). Example: tomato at peak demand (6 mm/day), plant spacing 0.5m × 1m = 0.5 m²: 6 × 0.5 × 0.85 = 2.55 L/day/plant.

3. Calculate total emitter output per plant: Total L/h = Number of emitters × Flow rate per emitter. Example: 2 emitters × 2 L/h = 4 L/h.

4. Calculate runtime: Hours = Water needed (L) ÷ Total emitter output (L/h). Example: 2.55 ÷ 4 = 0.64 hours = 38 minutes.

5. Adjust for soil type: Sandy soil: split into 2-3 shorter sessions (e.g., 15 min × 3) to reduce leaching. Clay soil: one longer session is fine, but don't exceed infiltration rate. Loam: one or two sessions.

Peak Water Requirements by Crop

Tomato: 4-7 mm/day (peak fruit production). Corn: 5-8 mm/day (tasseling/silking). Lettuce: 3-5 mm/day. Strawberry: 3-5 mm/day. Grape: 3-6 mm/day (veraison to harvest). Apple: 4-6 mm/day (fruit expansion). Alfalfa: 5-8 mm/day (regrowth after cutting). These are peak demands — reduce by 30-50% during establishment and late maturity stages.

Common Mistakes and Solutions

Over-Watering

Symptoms: yellow leaves, root rot, wilting despite wet soil, nutrient leaching (especially N), algae growth on soil surface. Causes: running too long, too frequent, wrong emitter size. Fix: reduce runtime by 20-30%, increase interval between waterings, check soil moisture with a probe or shovel (wet at 15-30 cm = adequate). Over-watering is more common and more damaging than under-watering in drip systems.

Under-Watering

Symptoms: wilting during hottest part of day (recovers at night = mild stress; doesn't recover = severe), small fruit, premature flowering, leaf curl. Causes: too short runtime, clogged emitters, insufficient pressure, wrong ET estimate. Fix: increase runtime by 20-30%, check and clean emitters, verify pressure, use local ET data. Mild water stress (wilting that recovers overnight) can actually improve fruit quality in some crops (grapes, tomatoes) but reduces yield.

Uneven Watering

Symptoms: some plants thrive, otherstruggle; streaks in the field; varying crop maturity. Causes: pressure variations (slope, long rows), clogged emitters, improper design (too many emitters one line), elevation changes. Fix: install pressuregulators, use pressure-compensating emitters, flush lines, redesign with shorterows or multiple zones, check elevation (each 1m elevation change = 1.4 psi pressure change).

Maintenance Schedule

Daily: check pressure gauge, look for leaks or broken lines, verify controller is running correctly. Weekly: inspect emitters for clogging, check soil moisture in 2-3 locations, flush end caps briefly. Monthly: flush main lines and submains, clean filters, check fertilizer injector ifertigating. Seasonally: pressure test system, replace damaged tubing, calibratemitter flow, winterize (blow out lines with compressed air in freezing climates). A well-maintainedrip system lasts 10-15 years; a neglected one may fail in 2-3 years.

Questions Fréquentes